Motors There are 30 products.

  • Available
    MG995 Metal Servo with Gears and Parts

    Working Torque: 13kg/cm; Rotate Speed : 53-62R/M; Bad Zone Setting : 4 microseconds; Connector: Universal JR / FUTABA; Rotation angle: 180 degree (max.); Working Voltage : 3.0V~7.2V; Working current: 100mA; Structure material: metal copper gear, coreless motor, dual ball bearings

    Working Torque: 13kg/cm; Rotate Speed : 53-62R/M; Bad Zone Setting : 4 microseconds;...

    Working Torque: 13kg/cm; Rotate Speed : 53-62R/M; Bad Zone Setting : 4 microseconds; Connector: Universal JR / FUTABA; Rotation angle: 180 degree (max.); Working Voltage :...

    7,40 €

    Add to cart View
  • Available
    Mini servo TowerPro SG90 9G

    Tower Pro SG90 is a high quality,low-cost servo for all your mechatronic needs. It comes with a 3-pin power and control cable, mounting hardware.

    Tower Pro SG90 is a high quality,low-cost servo for all your mechatronic needs. It...

    Tower Pro SG90 is a high quality,low-cost servo for all your mechatronic needs. It comes with a 3-pin power and control cable, mounting hardware.

    3,20 €

    Add to cart View
  • Motor/Stepper/Servo Shield
    Available
    Motor/Stepper/Servo Shield

    Arduino is a great starting point for electronics, and with a motor shield it can also be a nice tidy platform for robotics and mechatronics. This sheield can drive up to 4 bi-directional DC motors with individual speed selection or up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, interleaved or micro-stepping. It also have 2 connections for 5V servos.

    Arduino is a great starting point for electronics, and with a motor shield it can also...

    Arduino is a great starting point for electronics, and with a motor shield it can also be a nice tidy platform for robotics and mechatronics. This sheield can drive up to 4...

    5,30 €

    Add to cart View
  • Tower Pro MG90S 14G Mini Metal Gear Steering Servo
    Available
    Tower Pro MG90S 14G Mini Metal Gear Steering Servo

    Tower Pro MG90S analog metal giear mini servo. Weight: 13.4g, Dimension: 22.8*12.2*28.5mm, Stall torque: 1.8kg/cm(4.8V )2.2kg/cm(6V), Operating speed: 0.1sec/60degree(4.8v), 0.08sec/60degree(6v), Operating voltage: 4.8-6.0V, Dead band width: 5us, Modulation: Analog, Gear Type: Metal, Rotation/Support:  Dual Bearings

    Tower Pro MG90S analog metal giear mini servo. Weight: 13.4g, Dimension:...

    Tower Pro MG90S analog metal giear mini servo. Weight: 13.4g, Dimension: 22.8*12.2*28.5mm, Stall torque: 1.8kg/cm(4.8V )2.2kg/cm(6V), Operating speed: 0.1sec/60degree(4.8v),...

    5,60 €

    Add to cart View
  • DC gear (Reduction) motor P12 6V 70RPM
    Available
    DC gear (Reduction) motor P12 6V 70RPM

    Gear (reduction ) running a speed at 200rpm.All you need to do is connect the postive and  negative  pole-pin,simple enough for beginners. Torque: 2.5KG CM

    Gear (reduction ) running a speed at 200rpm.All you need to do is connect the postive...

    Gear (reduction ) running a speed at 200rpm.All you need to do is connect the postive and  negative  pole-pin,simple enough for beginners. Torque: 2.5KG CM

    6,30 €

    Add to cart View
  • Reduced price!  (-30%) Sena kaina: 8,40 €
    5,88 €

    Add to cart View
  • Futaba S3003 servo with accessories
    Out of stock
    Futaba S3003 servo with accessories

    Futaba S3003 Servo with accessories. Futaba S3003 servo is designed for car, ship and robot, compatible with Futaba, JR, Sanwa, Hitec control system.

    Futaba S3003 Servo with accessories. Futaba S3003 servo is designed for car, ship and...

    Futaba S3003 Servo with accessories. Futaba S3003 servo is designed for car, ship and robot, compatible with Futaba, JR, Sanwa, Hitec control system.

    7,95 €

    Add to cart View
  • Available
    5V Miniature Motor

    5V Miniature DC Motor. Length: 25mm, diameter: 21mm, shaft diameter: 2mm, shaft length: 9mm. Voltage :3-6V

    5V Miniature DC Motor. Length: 25mm, diameter: 21mm, shaft diameter: 2mm, shaft length:...

    5V Miniature DC Motor. Length: 25mm, diameter: 21mm, shaft diameter: 2mm, shaft length: 9mm. Voltage :3-6V

    Reduced price!  (-15%) Sena kaina: 1,20 €
    1,02 €

    Add to cart View
  • 8,90 €

    Add to cart View
  • 16-Channel 12-bit PWM/Servo Shield
    16,40 €

    Add to cart View
  • 11,50 €

    Add to cart View
  • A4988 žingsninio variklio valdymo modulis
    3,10 €

    Add to cart View
  • DRV8825 žingsninio variklio valdymo modulis
    4,40 €

    Add to cart View
  • CNC priedėlis
    Available
    CNC priedėlis

    8,20 €

    Add to cart View
  • Vibration motor
    Available
    Vibration motor

    Phone vibration motor is for DC brush motor for achieving the phone's vibration feature, when you receive a text message or phone, the motor starts to drive high-speed rotating eccentric done, resulting in vibration.

    Phone vibration motor is for DC brush motor for achieving the phone's vibration...

    Phone vibration motor is for DC brush motor for achieving the phone's vibration feature, when you receive a text message or phone, the motor starts to drive high-speed rotating...

    1,40 €

    Add to cart View
  • DC motor driver (L293D)
    Available
    DC motor driver (L293D)

    The Device is a monolithic integrated high voltage,high current four channel driver designed to accept standard DTL or TTL logic levels and drive inductive loads (such as relays solenoides, DC and stepping motors) and switching power transistors .To simplify use as two bridges each pair of channels is equipped with an enable input.

    The Device is a monolithic integrated high voltage,high current four channel driver...

    The Device is a monolithic integrated high voltage,high current four channel driver designed to accept standard DTL or TTL logic levels and drive inductive loads (such as relays...

    3,90 €

    Add to cart View
  • Available
    RAMPS 1.4 Reprap MendelPrusa 3D Printer Control Board

    The board is designed to be flexible in the user's power source availability, allowing for an ATX power supply to power the board, or the user can choose to install the voltage regulator kit for use with any power supply 7V-30V.The board features a developer friendly expansion port supporting I2C, SPI, UART, as well as a few ADC pins. All 14 expansion pins can be used as GPIO as well.

    The board is designed to be flexible in the user's power source availability, allowing...

    The board is designed to be flexible in the user's power source availability, allowing for an ATX power supply to power the board, or the user can choose to install the voltage...

    15,40 €

    Add to cart View
  • DC gear (Reduction) motor P12 6V 70RPM
    Available
    DC gear (Reduction) motor P12 6V 100RPM

    Gear (reduction ) running a speed at 100rpm.All you need to do is connect the postive and  negative  pole-pin,simple enough for beginners. Torque: 2.5KG CM

    Gear (reduction ) running a speed at 100rpm.All you need to do is connect the postive...

    Gear (reduction ) running a speed at 100rpm.All you need to do is connect the postive and  negative  pole-pin,simple enough for beginners. Torque: 2.5KG CM

    6,30 €

    Add to cart View
  • L298 Dual H-Bridge motor driver
    Available
    L298 Dual H-Bridge motor driver

    This module is based on the very popular L298 Dual H-Bridge Motor Driver Integrated Circuit. The circuit will allow you to easily and independently control two motors of up to 2A each in both directions. It is ideal for robotic applications and well suited for connection to a microcontroller requiring just a couple of control lines per motor. 

    This module is based on the very popular L298 Dual H-Bridge Motor Driver Integrated...

    This module is based on the very popular L298 Dual H-Bridge Motor Driver Integrated Circuit. The circuit will allow you to easily and independently control two motors of up to...

    Reduced price!  (-20%) Sena kaina: 4,90 €
    3,92 €

    Add to cart View
  • 1,90 €

    Add to cart View
  • Variklių valdiklis BTS7960
    22,90 €

    Add to cart View
  • 2 DC motor drive module, L298N
    Available
    2 DC motor drive module, MX1508

    L298N internal transistor switch, low efficiency, high fever, without heat, heavy volume, the market of MX1508 is easy to burn out, do not use the original chips, this product can be the perfect replacement.dual 1.5A*2, peak current to 2.5A, built-in overheat protection circuit,  automatic recovery after falling temperature. (the smart car voltage and current on the market are within this range)

    L298N internal transistor switch, low efficiency, high fever, without heat, heavy...

    L298N internal transistor switch, low efficiency, high fever, without heat, heavy volume, the market of MX1508 is easy to burn out, do not use the original chips, this product...

    2,60 €

    Add to cart View
  • DC variklių valdymo priedėlis (L298P)
    14,40 €

    Add to cart View
  • Available
    4 motor driver shield (1.2A, I2C)

    Instead of a L293D darlington driver, there are installed TB6612 MOSFET driver: with 1.2A per channel and 3A peak current capability. It also has much lower voltage drops across the motor so you get more torque out of your batteries, and there are built-in flyback diodes as well.

    Instead of a L293D darlington driver, there are installed TB6612 MOSFET driver: with...

    Instead of a L293D darlington driver, there are installed TB6612 MOSFET driver: with 1.2A per channel and 3A peak current capability. It also has much lower voltage drops across...

    18,40 €

    Add to cart View
  • Two DC motors driver shield (L298P)
    Out of stock
    Two DC motors driver shield (L298P)

    The Motor Shield is based on the L298 , which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. It lets you drive two DC motors with your board, controlling the speed and direction of each one independently. You can also measure the motor current absorption of each motor, among other features.

    The Motor Shield is based on the L298 , which is a dual full-bridge driver designed to...

    The Motor Shield is based on the L298 , which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. It lets you drive...

    15,40 €

    Add to cart View
  • DC gear (Reduction) motor P12 6V 70RPM
    Available
    DC gear motor 6V 30RPM (N20)

    Gear (reduction ) running a speed at 30rpm.All you need to do is connect the postive and  negative  pole-pin,simple enough for beginners.

    Gear (reduction ) running a speed at 30rpm.All you need to do is connect the postive...

    Gear (reduction ) running a speed at 30rpm.All you need to do is connect the postive and  negative  pole-pin,simple enough for beginners.

    6,30 €

    Add to cart View
  • Submersible Pump (3V/5V, 120L/H)
    Out of stock
    Submersible Pump (3V/5V, 120L/H)

    Mini submersible pump, voltage 3V/5V, flow rate 80-120L/H, max lift: 1.1m

    Mini submersible pump, voltage 3V/5V, flow rate 80-120L/H, max lift: 1.1m

    Mini submersible pump, voltage 3V/5V, flow rate 80-120L/H, max lift: 1.1m

    3,40 €

    Add to cart View
  • Available
    Water pump (RS-360SH, 7V, 1.2 l/min)

    Rated Voltage : DC 6-12V (if 12V, please do not use for long time. Marked with a red dot that Terminal is positive)

    Rated Voltage : DC 6-12V (if 12V, please do not use for long time. Marked with a red...

    Rated Voltage : DC 6-12V (if 12V, please do not use for long time. Marked with a red dot that Terminal is positive)

    4,90 €

    Add to cart View
  • Available
    TT DC Gear Motor

    TT DC Gear Motor for Smart Car Robot is a kind of DC deceleration motor. It is widely applied in the area of robots, smart cars, etc.. 

    TT DC Gear Motor for Smart Car Robot is a kind of DC deceleration motor. It is widely...

    TT DC Gear Motor for Smart Car Robot is a kind of DC deceleration motor. It is widely applied in the area of robots, smart cars, etc.. 

    2,90 €

    Add to cart View
  • 15,90 €

    Add to cart View