Arduino shealds There are 46 products.

  • Available
    Proto Screw Shield

    The ScrewShield extends all pins of the Arduino out to 3.5mm pitch screw terminals. It also has a lot of the utility provided by Arduino Protoshield, including: a large prototyping space of both connected and unconnected 0.1" spaced through-holes, a reset button, LED for D13 pin indicating.

    The ScrewShield extends all pins of the Arduino out to 3.5mm pitch screw terminals. It...

    The ScrewShield extends all pins of the Arduino out to 3.5mm pitch screw terminals. It also has a lot of the utility provided by Arduino Protoshield, including: a large...

    4,40 €

    Add to cart View
  • Available
    Arduino Sensor Shield

    Arduino sensor shield is specifically designed for Arduino board to connect to various types of electronic brick modules. It is compatible with the mainstream two interfaces of electronic bricks in the market: 2.0mm 4-pin grove interface and 2.54mm 3-pin interface. In addition, the shield is equipped with XBee interface for users to connect it with various external wireless modules.

    Arduino sensor shield is specifically designed for Arduino board to connect to various...

    Arduino sensor shield is specifically designed for Arduino board to connect to various types of electronic brick modules. It is compatible with the mainstream two interfaces of...

    5,90 €

    Add to cart View
  • Arduino sensor shield (V5.0)
    Available
    Arduino sensor shield (V5.0)

    The sensor shield v5.0 allows you to hoop up the sensors directly to Arduino Uno without the use of the breadboard. It allows plug and play connection to various modules like sensors, servos, relays, potentiometers and more. Everything is plug and play. So all you need to do is to read the data from the sensors and output PWM to drive the servos by program in arduino.

    The sensor shield v5.0 allows you to hoop up the sensors directly to Arduino Uno...

    The sensor shield v5.0 allows you to hoop up the sensors directly to Arduino Uno without the use of the breadboard. It allows plug and play connection to various modules like...

    4,90 €

    Add to cart View
  • Arduino Mega sensor shield (v2.0)
    Available
    Arduino Mega sensor shield (v2.0)

    Arduino Sensor Shield allows you to connect to various modules like sensors, servos, relays, buttons, potentiometers. Just plug & play. Each functional module has buckled port with VCC, GND and Output, which has corresponding port on the Sensor Shield, connected with a plain 2.54mm dual-female cable you may start playing already.

    Arduino Sensor Shield allows you to connect to various modules like sensors, servos,...

    Arduino Sensor Shield allows you to connect to various modules like sensors, servos, relays, buttons, potentiometers. Just plug & play. Each functional module has buckled...

    6,20 €

    Add to cart View
  • Available
    Arduino Nano IO shield

    Nano IO shield is a breakout board for Arduino Nano. It breaks out all pins as Electronic brick 3pin interface, the Zigbee XBee Series Modules and nRF24L01 wireless interface. And it supports 7-12V external power supply.

    Nano IO shield is a breakout board for Arduino Nano. It breaks out all pins as...

    Nano IO shield is a breakout board for Arduino Nano. It breaks out all pins as Electronic brick 3pin interface, the Zigbee XBee Series Modules and nRF24L01 wireless interface....

    6,20 €

    Add to cart View
  • Available
    Prototype Shield with Mini Breadboard for Arduino

    Build a prototype circuit, can be directly welded components on board, also be able to connect the mini bread plate above circuit. ProtoShield prototype extension plate with two LED and button circuit, can be used directly, and all the pins and power have been draw out, very suitable for building prototype circuit with Arduino. A product for Arduino that works with official Arduino boards.

    Build a prototype circuit, can be directly welded components on board, also be able to...

    Build a prototype circuit, can be directly welded components on board, also be able to connect the mini bread plate above circuit. ProtoShield prototype extension plate with two...

    4,20 €

    Add to cart View
  • Prototype Shield with Mini Breadboard for Arduino Mega
    Available
    Prototype Shield with Mini Breadboard for Arduino Mega

    This is a design for an open-source prototyping Mega shield for Arduino Mega2560. It has tons of cool features, to make prototyping on your Arduino easy. This shield include a mini breadboard, two LED and button circuit.  Very suitable for building prototype circuit with Arduino. A product for Arduino that works with official Arduino boards.

    This is a design for an open-source prototyping Mega shield for Arduino Mega2560. It...

    This is a design for an open-source prototyping Mega shield for Arduino Mega2560. It has tons of cool features, to make prototyping on your Arduino easy. This shield include a...

    Reduced price!  (-30%) Sena kaina: 7,50 €
    5,25 €

    Add to cart View
  • Available
    Arduino ProtoShield KIT

    The ProtoShield mates with the Arduino USB board and gives the user a small soldering area, two general LEDs, access to a BlueSMiRF socket, a general pushbutton switch, and most important of all - the Arduino reset switch is brought to the top level.

    The ProtoShield mates with the Arduino USB board and gives the user a small soldering...

    The ProtoShield mates with the Arduino USB board and gives the user a small soldering area, two general LEDs, access to a BlueSMiRF socket, a general pushbutton switch, and most...

    7,19 €

    Add to cart View
  • Available
    XBee Shield

    XBee Shield is an enhanced Zigbee XBee Series modules breakout board for Arduino, it can directly plug in with Arduino, and use any pin of the basic board to connect with the XBee module serial port.

    XBee Shield is an enhanced Zigbee XBee Series modules breakout board for Arduino, it...

    XBee Shield is an enhanced Zigbee XBee Series modules breakout board for Arduino, it can directly plug in with Arduino, and use any pin of the basic board to connect with the...

    8,90 €

    Add to cart View
  • Multifunctional shield
    5,40 €

    Add to cart View
  • Available
    1602 LCD Shield

    This is a very popular LCD Keypad shield for Arduino board. It can be directly plugged on the Arudino board, no soldering or fly-wiring needed, it offer the 16x2 characters display and 6 buttons for Arduino.This Shield uses Arudino LCD library.

    This is a very popular LCD Keypad shield for Arduino board. It can be directly plugged...

    This is a very popular LCD Keypad shield for Arduino board. It can be directly plugged on the Arudino board, no soldering or fly-wiring needed, it offer the 16x2 characters...

    Reduced price!  (-13%) Sena kaina: 6,80 €
    5,92 €

    Add to cart View
  • LCD shield with rotary encoder
    Available
    LCD shield with rotary encoder

    LCD Key Shield is an LCD expansion board with a 1602 LCD display , a five-way key, a rotary encoder. It is fully compatible with the Arduino UNO board.

    LCD Key Shield is an LCD expansion board with a 1602 LCD display , a five-way key, a...

    LCD Key Shield is an LCD expansion board with a 1602 LCD display , a five-way key, a rotary encoder. It is fully compatible with the Arduino UNO board.

    11,95 €

    Add to cart View
  • Out of stock
    TFT1.8SP Shield

    TFT1.8 Shield is the 1.8-inch LCD SPI serial expansion board with dual SD card socket, as the SPI serial 1.8-inch LCD operating voltage is 3.3V, 3.3V LDO regulator circuit is added to the shield, therefore, you can directly use 5V power supply. It is fully compatible with Arduino UNO board, so you can achieve the required functionality only by assembling the TFT1.8 Shield with the Arduino board. .

    TFT1.8 Shield is the 1.8-inch LCD SPI serial expansion board with dual SD card socket,...

    TFT1.8 Shield is the 1.8-inch LCD SPI serial expansion board with dual SD card socket, as the SPI serial 1.8-inch LCD operating voltage is 3.3V, 3.3V LDO regulator circuit is...

    15,45 €

    Add to cart View
  • Out of stock
    TFT2.2SP Shield

    TFT2.2_Serial_Shield is the 2.2-inch LCD SPI serial expansion board with SD card socket, as the SPI serial 2.2-inch LCD operating voltage is 3.3V, 3.3V LDO regulator circuit is added to the shield, therefore, you can directly use the 5V power supply. It is fully compatible with Arduino UNO board, so you can achieve the required functionality only by assembling the Shield with the Arduino board.

    TFT2.2_Serial_Shield is the 2.2-inch LCD SPI serial expansion board with SD card...

    TFT2.2_Serial_Shield is the 2.2-inch LCD SPI serial expansion board with SD card socket, as the SPI serial 2.2-inch LCD operating voltage is 3.3V, 3.3V LDO regulator circuit is...

    18,45 €

    Add to cart View
  • Available
    2.8" TFT LCD Touch Shield

    Arduino 2.8'' TFT Touch Shield is an Arduino UNO/ Mega compatible multicolored TFT display with a touch-screen and SD card socket. It is available in an Arduino shield compatible pinout for attachment. The TFT driver is based on ILI9325DS with 8bit data and 4bit control interface.

    Arduino 2.8'' TFT Touch Shield is an Arduino UNO/ Mega compatible multicolored TFT...

    Arduino 2.8'' TFT Touch Shield is an Arduino UNO/ Mega compatible multicolored TFT display with a touch-screen and SD card socket. It is available in an Arduino shield...

    22,95 €

    Add to cart View
  • 3.2 TFT LCD Touch Shield
    Available
    3.2 TFT LCD Touch Shield

    Arduino 3.2'' TFT Touch Shield is an Arduino Mega compatible multicolored TFT display with a touch-screen and SD card socket. It is available in an Arduino MEGA shield compatible pinout for attachment. The TFT driver is based on SSD1289 with 16bit data and 4bit control interface.

    Arduino 3.2'' TFT Touch Shield is an Arduino Mega compatible multicolored TFT display...

    Arduino 3.2'' TFT Touch Shield is an Arduino Mega compatible multicolored TFT display with a touch-screen and SD card socket. It is available in an Arduino MEGA shield...

    25,95 €

    Add to cart View
  • Available
    BLE Development Shield

    The BLE Development Shield for BLEduino is specially designed for BLEduino (BLE with Arduino Uno). Together with BLEduino, this BLE Shield forms an ideal prototyping platform for both software and hardware developers to go wireless. You will be able to develop your own smart bracelet, smart pedometer, etc. It's a low-power, real-time low energy communication perfect for embedded designs.

    The BLE Development Shield for BLEduino is specially designed for BLEduino (BLE with...

    The BLE Development Shield for BLEduino is specially designed for BLEduino (BLE with Arduino Uno). Together with BLEduino, this BLE Shield forms an ideal prototyping platform...

    16,90 €

    Add to cart View
  • Out of stock
    TFT LCD ITDB02 Arduino Shield

    The ITDB02 LCD module is work in 3.3V voltage level and it's not compatible with Arduino pins , so we make a shield for Arduino to connect with these LCDs. Now user can directly plug the ITDB02 Series LCDs in the shield and stand on the Arduino board.

    The ITDB02 LCD module is work in 3.3V voltage level and it's not compatible with...

    The ITDB02 LCD module is work in 3.3V voltage level and it's not compatible with Arduino pins , so we make a shield for Arduino to connect with these LCDs. Now user can directly...

    7,22 €

    Add to cart View
  • Available
    TFT LCD ITDB02 Arduino MEGA Shield

    The ITDB02 Series LCD module works in 3.3V voltage level and it's not compatible with Arduino MEGA pins , so we make a shield for Arduino MEGA. Now user can directly plug the ITDB02 in the shield and stand on the Arduino MEGA board.

    The ITDB02 Series LCD module works in 3.3V voltage level and it's not compatible with...

    The ITDB02 Series LCD module works in 3.3V voltage level and it's not compatible with Arduino MEGA pins , so we make a shield for Arduino MEGA. Now user can directly plug the...

    8,40 €

    Add to cart View
  • Motor/Stepper/Servo Shield
    Available
    Motor/Stepper/Servo Shield

    Arduino is a great starting point for electronics, and with a motor shield it can also be a nice tidy platform for robotics and mechatronics. This sheield can drive up to 4 bi-directional DC motors with individual speed selection or up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, interleaved or micro-stepping. It also have 2 connections for 5V servos.

    Arduino is a great starting point for electronics, and with a motor shield it can also...

    Arduino is a great starting point for electronics, and with a motor shield it can also be a nice tidy platform for robotics and mechatronics. This sheield can drive up to 4...

    5,30 €

    Add to cart View
  • Available
    MotoMama

    MotoMama is a motor drivers shield for Arduino, based on L298N H-bridge driver chip. You can use this shield to drive two DC motors or an four-wire two-phase stepper motors with Arduino boards.

    MotoMama is a motor drivers shield for Arduino, based on L298N H-bridge driver chip....

    MotoMama is a motor drivers shield for Arduino, based on L298N H-bridge driver chip. You can use this shield to drive two DC motors or an four-wire two-phase stepper motors with...

    12,90 €

    Add to cart View
  • DC variklių valdymo priedėlis (L298P)
    14,40 €

    Add to cart View
  • Available
    L298 Motor Shield (SHD-L298N)

    Motor Shield (2A) uses L298P chip which allow to drive two 7-12V DC motors with maximum 2A current. This shield can be directly mount onto standard Arduino Duemilanoveand Arduino Mega.

    Motor Shield (2A) uses L298P chip which allow to drive two 7-12V DC motors with maximum...

    Motor Shield (2A) uses L298P chip which allow to drive two 7-12V DC motors with maximum 2A current. This shield can be directly mount onto standard Arduino Duemilanoveand...

    19,40 €

    Add to cart View
  • Available
    4 motor driver shield (1.2A, I2C)

    Instead of a L293D darlington driver, there are installed TB6612 MOSFET driver: with 1.2A per channel and 3A peak current capability. It also has much lower voltage drops across the motor so you get more torque out of your batteries, and there are built-in flyback diodes as well.

    Instead of a L293D darlington driver, there are installed TB6612 MOSFET driver: with...

    Instead of a L293D darlington driver, there are installed TB6612 MOSFET driver: with 1.2A per channel and 3A peak current capability. It also has much lower voltage drops across...

    18,40 €

    Add to cart View
  • Available
    Dual Step Motor Driver Shield

    Dual stepper motor driver shield can drive 2 stepper motors at the same time by Arduino. It can work with the power supply from 4.75V to 30V. High accuracy controlling can be supported by Arduino for CNC milling machine. It uses  A3967SLB  microstepping motor driver.

    Dual stepper motor driver shield can drive 2 stepper motors at the same time by...

    Dual stepper motor driver shield can drive 2 stepper motors at the same time by Arduino. It can work with the power supply from 4.75V to 30V. High accuracy controlling can be...

    14,90 €

    Add to cart View
  • CNC priedėlis
    Available
    CNC priedėlis

    8,20 €

    Add to cart View
  • 16-Channel 12-bit PWM/Servo Shield
    16,40 €

    Add to cart View
  • Available
    IS Shield

    IS Shield is a relay shield for Arduino, with 2 channels mechanical relays and 2 channels MOS switch, providing an easy way for applications of voltage controlling from low to high.

    IS Shield is a relay shield for Arduino, with 2 channels mechanical relays and 2...

    IS Shield is a relay shield for Arduino, with 2 channels mechanical relays and 2 channels MOS switch, providing an easy way for applications of voltage controlling from low to...

    Reduced price!  (-3%) Sena kaina: 14,40 €
    13,90 €

    Add to cart View
  • Out of stock
    GPS shield

    Arduino GPS shield is a GPS module breakout board for Arduino. It can make your Arduino as a GPS receiver with SD storage, it is easy to use for recording the position data into SD card by Arduino

    Arduino GPS shield is a GPS module breakout board for Arduino. It can make your Arduino...

    Arduino GPS shield is a GPS module breakout board for Arduino. It can make your Arduino as a GPS receiver with SD storage, it is easy to use for recording the position data into...

    Reduced price!  (-21%) Sena kaina: 35,90 €
    28,40 €

    Add to cart View
  • Available
    Bluetooth shield

    The Bluetooth Shield integrates a Serial Bluetooth module. It can be easily used with Arduino/Iteaduino for transparent wireless serial communication. You can choose two pins from Arduino D0 to D7 as Software Serial Ports to communicate with Bluetooth Shield (D0 and D1 is Hardware Serial Port).

    The Bluetooth Shield integrates a Serial Bluetooth module. It can be easily used with...

    The Bluetooth Shield integrates a Serial Bluetooth module. It can be easily used with Arduino/Iteaduino for transparent wireless serial communication. You can choose two pins...

    14,80 €

    Add to cart View
  • W5100 Ethernet Shield
    Available
    W5100 Ethernet Shield

    W5100 Ethernet shield is a WIZnet W5100 breakout board with POE and Micro-SD card designed for Arduino platform. 5V/3.3V compatible operation voltage level makes it compatible with Arduino boards, leafmaple, and other Arduino compatible board.

    W5100 Ethernet shield is a WIZnet W5100 breakout board with POE and Micro-SD card...

    W5100 Ethernet shield is a WIZnet W5100 breakout board with POE and Micro-SD card designed for Arduino platform. 5V/3.3V compatible operation voltage level makes it compatible...

    9,40 €

    Add to cart View
  • CAN-BUS Shield
    Available
    CAN-BUS Shield

    The CAN-BUS is a common industrial bus because of its long travel distance, medium communication speed and high reliability. It is commonly found on modern machine tools and as an automotive diagnostic bus. With an OBD-II converter cable added on and the OBD-II library imported, you are ready to build an onboard diagnostic device or data logger.

    The CAN-BUS is a common industrial bus because of its long travel distance, medium...

    The CAN-BUS is a common industrial bus because of its long travel distance, medium communication speed and high reliability. It is commonly found on modern machine tools and as...

    13,90 €

    Add to cart View
  • 34,40 €

    Add to cart View
  • Out of stock
    Arduino Wireless Programmer

    Arduino Wireless Programmer is designed for uploading the program from your PC/laptop to Arduino board just by Bluetooth. Use with this programmer you can upload the code via wireless instead of using USB cable, it will be very useful for updating the code to the Arduino board which in the box or case.

    Arduino Wireless Programmer is designed for uploading the program from your PC/laptop...

    Arduino Wireless Programmer is designed for uploading the program from your PC/laptop to Arduino board just by Bluetooth. Use with this programmer you can upload the code via...

    11,22 €

    Add to cart View
  • Out of stock
    RFID reader shield SHD-NFC

    RFID/NFC Shield is a Near Field Communication interface for Arduino build around the popular NXP PN532 integrated circuit and SPI communication between Arduino and NFC Shield.. RFID/NFC is a short-distance radio technology that enables communication between devices that are held close together. Use as a RFID reader with Mifare One tags (ISO14443 Type-A) and cards (13.56Mhz).

    RFID/NFC Shield is a Near Field Communication interface for Arduino build around the...

    RFID/NFC Shield is a Near Field Communication interface for Arduino build around the popular NXP PN532 integrated circuit and SPI communication between Arduino and NFC Shield.....

    26,20 €

    Add to cart View
  • Available
    Stackable SD Card shield

    Stackable SD card shield is a standard SD card / TF card break out board for Arduino. The SD card shield adds storage to your Arduino project. It supports SD, SDHC, or MicroSD TF cards. It just uses the SPI ports of Arduino,and you can plug more other shield on it.

    Stackable SD card shield is a standard SD card / TF card break out board for Arduino....

    Stackable SD card shield is a standard SD card / TF card break out board for Arduino. The SD card shield adds storage to your Arduino project. It supports SD, SDHC, or MicroSD...

    4,90 €

    Add to cart View
  • Available
    IBridge lite

    IBridge lite is a 3X3 key-pad shield with a 5110 Graphic LCD interface. It is compatible with Arduino, you can plug it on Arduino board directly, and get a small development platform with keypad input and Graphic LCD display.

    IBridge lite is a 3X3 key-pad shield with a 5110 Graphic LCD interface. It is...

    IBridge lite is a 3X3 key-pad shield with a 5110 Graphic LCD interface. It is compatible with Arduino, you can plug it on Arduino board directly, and get a small development...

    7,90 €

    Add to cart View
  • Duomenų kaupimo priedėlis
    7,90 €

    Add to cart View
  • Available
    Joystick shield

    You can use the Joystick shield sits on top of your Arduino and turns it into a simple controller. 7 momentary push buttons and a two-axis thumb joystick gives your Arduino functionality on the level of old Nintendo controllers.

    You can use the Joystick shield sits on top of your Arduino and turns it into a simple...

    You can use the Joystick shield sits on top of your Arduino and turns it into a simple controller. 7 momentary push buttons and a two-axis thumb joystick gives your Arduino...

    6,90 €

    Add to cart View
  • Available
    Touch Shield

    The MPR121 IC is a great way to build simple capacitive touch interfaces, and now it's even easier to incorporate into your Arduino projects with the touch shield. The touch shield has12 capacitive touch pads. With this shield you can have a total of 12 touch sensitive buttons. An on-board logic level converter allows it to work with 5V and 3.3V Arduino boards.

    The MPR121 IC is a great way to build simple capacitive touch interfaces, and now it's...

    The MPR121 IC is a great way to build simple capacitive touch interfaces, and now it's even easier to incorporate into your Arduino projects with the touch shield. The touch...

    7,90 €

    Add to cart View
  • Out of stock
    Power shield

    Power Shield is a portable offline power supply board for Arduino. Using two AAA batteries and with high-efficiency DC-DC boost circuit, this shield is the power source which can output 5V/350mA. Standard Arduino pin map makes it compatible with Iteaduino series and other Arduino compatible board.

    Power Shield is a portable offline power supply board for Arduino. Using two AAA...

    Power Shield is a portable offline power supply board for Arduino. Using two AAA batteries and with high-efficiency DC-DC boost circuit, this shield is the power source which...

    8,40 €

    Add to cart View
  • Available
    RAMPS 1.4 Reprap MendelPrusa 3D Printer Control Board

    The board is designed to be flexible in the user's power source availability, allowing for an ATX power supply to power the board, or the user can choose to install the voltage regulator kit for use with any power supply 7V-30V.The board features a developer friendly expansion port supporting I2C, SPI, UART, as well as a few ADC pins. All 14 expansion pins can be used as GPIO as well.

    The board is designed to be flexible in the user's power source availability, allowing...

    The board is designed to be flexible in the user's power source availability, allowing for an ATX power supply to power the board, or the user can choose to install the voltage...

    15,40 €

    Add to cart View
  • Two DC motors driver shield (L298P)
    Out of stock
    Two DC motors driver shield (L298P)

    The Motor Shield is based on the L298 , which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. It lets you drive two DC motors with your board, controlling the speed and direction of each one independently. You can also measure the motor current absorption of each motor, among other features.

    The Motor Shield is based on the L298 , which is a dual full-bridge driver designed to...

    The Motor Shield is based on the L298 , which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. It lets you drive...

    15,40 €

    Add to cart View
  • Available
    ESP8266 shield

    13,90 €

    Add to cart View
  • 21,90 €

    Add to cart View
  • 17,40 €

    Add to cart View